Fast handoff with reducing waste rate approach for wireless resources management in UMTS mobile networks

3G Wideband CDMA systems adopt the Orthogonal Variable Spreading Factor code tree as the channelization codes management for achieving high data rate transmission in personal multimedia communications. It assigns a single channelization code for each accepted connection. Nevertheless, it wastes the system capacity when the required rate is not powers of two of the basic rate. One good solution is to assign multiple codes for each accepted connection but it causes two inevitable drawbacks: long handoff delay and new call setup delay due to high complexity of processing with multiple channelization codes, and high cost of using more number of rake combiners. Especially, long handoff delay may result in more call dropping probability and higher Grade of Service, which will degrade significantly the utilization and revenue of the 3G cellular systems. Therefore, we propose herein an adaptive efficient codes determination algorithm based on the Markov Decision Process analysis approach to reduce the waste rate and reassignments significantly while providing fast handoff. Numerical results demonstrate that the proposed approach yields several advantages, including the lowest GOS, the least waste rate, and the least number of reassignments. Meanwhile, the optimal number of rake combiners is also analyzed in this paper. This research was supported in part by the National Science Council of Taiwan, ROC, under contract NSC-93-2213-E-324-018.     

水力射孔对套管强度的影响研究

水力射孔技术是一种新型的完井方式，深穿透水力射孔技术辅助定向水力压裂可以实现油气层改造和油气井增产。但是，水力射孔套管会在孔眼处造成应力集中，使得局部应力过大而削弱了套管和水泥环的强度，可能会影响套管的使用寿命。因此，文章利用有限元软件建立了射孔套管的三维有限元模型，分析了水力射孔后套管管体的应力分布，重点研究了水力射孔参数-孔密、孔径、孔深、射孔方位角等对套管强度的影响规律。分析结果表明，沿着最大水平地应力方向深穿透水力射孔，选择合适的孔密、孔径可将射孔对套管的损害降至最小。研究结果为提高水力射孔完井设计水平提供了一定的参数依据。     

燃气管网动态仿真的研究及应用

研究和了解燃气在管道中的流动，是进行燃气管网系统优化和提高管网输运系统安全性的前提和基础。以流体力学三大守恒方程为基础，建立了等温和非等温条件下的燃气管网稳态和动态仿真理论模型。以有限差分法为基础，得到了上述模型的求解方法，并加入了耗散项，提高了求解方法的稳定性。通过增加初始点和延长出口点的方法，简化了模型的求解。通过在北京六环天然气管网中的初步应用，分别得到了与实际值综合相对误差为1.21％和2.62％的压力和流量仿真值，从而验证了模型及求解方法的可靠性。     

多带抗噪声语音识别算法研究

根据Flether等人的研究,基于感知独立性假设的子带识别方法被用于抗噪声鲁棒语音识别。本文拓展子带方法,采用基于噪声污染假定的多带框架来减少噪声影响。论文不仅从理论上分析了噪声污染假定多带框架在识别性能上的潜在优势,而且提出了多带环境下的鲁棒语音识别算法。研究表明：多带框架不仅回避了独立感知假设要求,而且与子带方法相比,多带方法能更好的减少噪声影响,提高系统识别性能。     

大型弧形闸门静力特性有限元分析

以某水电站溢洪道弧形闸门为例,建立了大型弧形闸门的有限元分析模型,应用ANSYS软件对其在各种工况下的支铰反力、闸门应力、位移挠度以及屈曲失稳等静力特性进行了计算分析,为完善闸门结构的设计提供了依据,对同类闸门结构的设计计算有参考意义。     

On the effects of the packet size distribution on the packet loss process

Real-time multimedia applications have to use forward error correction (FEC) anderror concealment techniques to cope with losses in today’s best-effort Internet. The efficiency of these solutions is known however to depend on the correlation between losses in the media stream. In this paper we investigate how the packet size distribution affects the packet loss process, that is, the distribution of the number of lost packets in a block, the related FEC performance and the average loss run length. We present mathematical models for the loss process of the MMPP+M/D/1/K and the MMPP+M/M/1/K queues; we validate the models via simulations, and compare the results to simulation results with an MPEG-4 coded video trace. We conclude that the deterministic packet size distribution (PSD) not only results in lower stationary loss probability than the exponential one, but also gives a less correlated loss process, both at a particular average link load and at a particular stationary loss probability as seen by the media stream.Our results show that for applications that can only measure the packet loss probability, the effects of the PSD on FEC performance are higher in access networks, where a single multimedia stream might affect the multiplexing behavior. Our results show that the effects of the PSD on FEC performance are higher in access networks, where a single multimedia stream might affect the multiplexing behavior and thus can improve the queuing performance by decreasing the variance of its PSD.     

基于振动参数的钻井井架安全承载力评定

通过井架结构振动理论、有限元分析和实验室简易模型的试验研究，提出了以振动频率为基准，载荷下降系数为依据诊断钻井井架结构安全承载能力的方法。根据井架的具体结构形式和受力特征，将井架简化成一根沿长度上质量均匀分布、刚度恒定的简支梁，用振动理论推导出了井架固有频率的平方与作用载荷之间存在着线性关系，并通过有限元分析对这一关系进行了验证；提出了通过测试井架在两种不同栽荷作用下的固有频率推算井架临界承载并以此评定井架安全承载能力的方法；在实验室内制作了与A型井架相类似的模型，进行了逐级载荷下的固有频率测试，分析总结出适用于井架现场评定的具体方法，最后应用此方法对现场在役井架进行了测试与安全承载能力评定。该评定方法为井架测试、安全评定提供了一个新的发展方向，对保证钻井安全将起到重要的作用。     

Fatigue crack propagation of multiple coplanar cracks with the coupled extended finite element/fast marching method

A numerical technique for modeling fatigue crack propagation of multiple coplanar cracks is presented. The proposed method couples the extended finite element method (X-FEM) [Int. J. Numer. Meth. Engng. 48 (11) (2000) 1549] to the fast marching method (FMM) [Level Set Methods & Fast Marching Methods: Evolving Interfaces in Computational Geometry, Fluid Mechanics, Computer Vision, and Materials Science, Cambridge University Press, Cambridge, UK, 1999]. The entire crack geometry, including one or more cracks, is represented by a single signed distance (level set) function. Merging of distinct cracks is handled naturally by the FMM with no collision detection or mesh reconstruction required. The FMM in conjunction with the Paris crack growth law is used to advance the crack front. In the X-FEM, a discontinuous function and the two-dimensional asymptotic crack-tip displacement fields are added to the finite element approximation to account for the crack using the notion of partition of unity [Comput. Meth. Appl. Mech. Engng. 139 (1996) 289]. This enables the domain to be modeled by a single fixed finite element mesh with no explicit meshing of the crack surfaces. In an earlier study [Engng. Fract. Mech. 70 (1) (2003) 29], the methodology, algorithm, and implementation for three-dimensional crack propagation of single cracks was introduced. In this paper, simulations for multiple planar cracks are presented, with crack merging and fatigue growth carried out without any user-intervention or remeshing.     

多业务移动通信系统中的呼叫接入控制

在多业务无线移动通信系统的呼叫接入控制中,不仅要考虑业务之间的优先级,同时也必须考虑切换呼叫的优先级。本文结合可移动边界算法和保护信道策略,提出了一种有效的多业务呼叫接入控制算法。为了方便地分析方案的性能,设计了一个二维的Markov链对方案的性能进行理论上的分析。通过数值分析结果表明,提出的算法同时保证了两种优先级,并提高了系统的性能。1     

面积坐标法构造含转角自由度的四结点膜元

以四边形面积坐标作为工具,构造了两个含转角自由度的广义协调四边形单元AQ4和lAQ4。它们通过强式分片检验,与同类单元相比,具有很高的计算精度,能消除梯形闭锁现象,有很强的抗网格畸变的能力。